Why dryers wont heat

In order for the gas to actually heat the dryer, it must first be ignited by the igniter. While a gas igniter can also be tested using a multimeter, we strongly suggest hiring a professional for any gas dryer repair issue. Safety is the primary concern when working with flammable gas. On many models of dryers, the timer controls the various functions of the dryer.

The main control board is the part that controls all of the other parts of your dryer. This is one of the most important components on the whole unit. If this piece is broken, there is a good chance it will be an expensive fix.

Dryers are designed with a thermostat that tells the computer when the clothes have reached the correct temperature. This is how the machine knows when to switch the heating element on or off. Mis-Fuelling Mis-fuelling is when a vehicle filled with the wrong type of fuel ex. Considering misfuelling commonality we have included it in your cover plan when you choose 24 7. You can call to 24 7 team if this should ever happen to you.

Home Start We acknowledge that a breakdown may occur outside your own home and will work to rectify any issue you may have. Nationwide Coverage We will spare no time to provide you with roadside assistance as we work with the largest breakdown network in the UK. We use cookies to improve your browsing experience. By using this website, you consent to our use of cookies. For further information, please see our cookies policy. DIY: Refrain from checking how your clothes are drying up before the appliance finishes its cycle.

Contact a tumble dryer engineer to check the NTC temperature sensor for an open or short circuit and its resistance to various temperatures. DIY: Clean the lint filter every time after each cycle. DIY: Reset the dyer and check again. DIY: Reset the machine.

It usually happens due to a defective thermistor, which should be replaced. Different results call for thermostat replacement. Temperature sensor has detected an open or shorted circuit 5 flashes may appear, depending on the model. Thermal Fuse If your dryer is tumbling but no longer producing heat, your first suspect should be the thermal fuse.

Exhaust Vent If your thermal fuse was responsible for the issue, your first course of action after replacing it should be to check your dryer vent. Thermostat and Temperature Switch The thermostat and temperature switch is responsible for keeping an even temperature inside your dryer.

Heating Coils If your thermal fuse was fine and the thermometer checked out, it is likely that the cause of no heat to your otherwise working dryer is due to faulty heating coils. Timer A faulty timer on mechanical-based models seems like it would have little to do with your dryer not producing heat. Leave a Reply Cancel Reply You must be logged in to post a comment.

Schedule Service. Customer Reviews. Check Your Job Status. What We Service. Where We Service. About Our Service. News and Tips. Leave a Review. Contact Service. Maybe you just overloaded it a bit, so you run a second, shorter cycle to finish the job.

This may be the worst problem of all: Everything seems like it's working mostly as it should be, but the problem gradually gets worse over time until you realize the clothes are still sopping wet after a full cycle. The culprit here could be a faulty heating element. If the heating element isn't working properly, the dryer will still spin and the cycle will complete, but it won't get hot enough to help dry the clothes.

Heating elements can naturally wear out over time, but overloading the dryer, not cleaning the lint screen and poor ventilation can all speed up that process. Fortunately, replacing a heating element isn't a terribly difficult job. You can usually find a replacement heating element at a local hardware store or online by searching for your dryer model number.

Once you have the part, unplug the dryer, remove the back panel, remove the connections and install the new one. Some heating elements may require you to remove the existing thermostat from the old heating element and install it on the new one.

Reattach the back panel, reconnect power and run a test cycle to check for heat. Another possible cause is clogged duct work. When was the last time you cleaned out the dryer vent anyway? No, not the lint screen -- the vent pipe. The obvious solution is to clean out the duct. It's not as bad as it may seem either. This should be done every six months to a year to not only keep your dryer running smoothly and efficiently, but also to prevent or reduce the risk of fire.